Menu
man getting told what to do when you run out of gas

Do you Know What to do When you Run Out of Gas? Do This Trick

Do you know what to do when you run out of gas? Before you get mad and leave because you think its a dumb question, just hang in there while I show you how to get yourself back on the road in no time.

They used to call it “driver’s education:” It was that 20 minutes you spent on the side of the road with a wrench, a cup full of gasoline and the sincere terror that the engine might backfire while you were pouring the gas under the hood.

Run out of gas one time in a car with a mechanical fuel pump and the ensuing experience will teach you all about the importance of keeping fuel in your tank. Restarting a modern car with an electric fuel pump is a far simpler and less dangerous affair than restarting an older auto, which is kind of a shame when you think about it.

Mechanical Fuel Pump vs. Electric Fuel Pumps

Before electronic fuel injection became mainstream in the 1970s, automobiles required a mechanical pump to pour fuel into the carburetor’s fuel bowls. Fluid pressure was important but not as important as fluid flow volume.

So most engines used engine-driven fuel pumps that sucked fuel from the tank and fed it to the carburetor. But fuel injection systems require a great deal more pressure, and electronic fuel pumps came into use. Unlike earlier pumps, which required the engine to run in order to pump fuel from the tank, electric pumps could move fuel with or without the engine running.

Immersion Filling

The first step to getting your car running is to put gas in the tank, and as much as possible. Electric fuel pumps have anti-drain back valves to maintain pressure for a little while after the pump shuts down, but those valves aren’t perfect. Usually, the fuel pump mechanism sits higher than the pump pickup in the bottom of the tank.

Running the fuel level below the pickup means running out of gas and stalling. When you refill your tank with a gallon or 2 of gas, you’re just barely covering the pickup and forcing the dry pump internals to suck fuel upward. Filling your gas tank completely full will gravity-force fuel into the pump’s internals, priming it more quickly and helping to get the fuel to your engine without undue drain on the battery.

Resetting the Pump

You may have noticed when your engine stalled for lack of gas that it bucked and coughed several times before stalling; this happens because just before running completely dry, the fuel pump inhaled little bubbles of air. That air worked its way to your engine in the form of bubbles, which got bigger and bigger until the motor died from lack of fuel pressure. Modern cars often have provisions to shut down the fuel pump using a standalone circuit breaker. This breaker is designed to trip in an accident, shutting down fuel flow and preventing fire.

In late-model autos, the engine computer may trip the breaker when it detects a loss of fuel pressure. For this reason, you may need to press the pump rest button after running out of gas. You’ll often find it above the driver’s foot well, under the carpet in your trunk, in the glove compartment, under the center console or under the front seats near the air bag’s inertia sensor. Check your car’s owner manual for the device’s exact location.

The Run Out of Gas Procedure

Once you have the gas tank filled and the pump switch reset, turn your ignition key to the “on” position and listen for the pump; you should hear it very distinctly at first, buzzing or humming, but it will quickly drop to a quiet hum as it fills up with fuel. Leave the ignition on for three to five seconds, then turn it off; then turn it on for three to five seconds again, then off again.

On some cars, the lack of fuel pressure will trigger another pump shutdown, so you don’t want to let the pump whir away for more than a few seconds at a time. Repeat three to four times to pressurize the system, then attempt to start the car. It should fire up almost immediately, though there may be a bit of lag or a cough as the air clears from the injector nozzles.

Watch out for This Once you Get it Started

If your check-engine light comes on after you’ve restarted the car, don’t just assume it’s a hangover from the stalling and your computer’s just harmlessly waiting for you to clear the codes. Once you get the car started, immediately drive it to a mechanic, dealer or auto parts store to have its diagnostic trouble codes cleared and the check engine light reset. Even with a protective shutdown switch, running out of gasoline and running the fuel pump dry can result in damage to the pump.

Your computer will detect fluctuations in fuel pressure and trigger the check-engine light to warn you — and it might be doing just that when you start the car. But you won’t know unless you clear the existing codes to see if the light comes on again. If it does, have the codes checked; if the code for low fuel pressure has been triggered, then you’re likely to soon be either buying a new fuel pump or getting a bit more education in walking.

About Author
mm

Collin Whittaker

My name is Collin and I am the editor and founder of My Used Car Blog. A little bit about my background – I’ve been an automotive technician for 10 plus years and I have worked for companies like Honda, Nissan, and other major automotive repair shops. I am a husband and a dad to three beautiful kids. My reason for starting this blog/website stems from my love and passion for the automotive industry. I will provide expert and insightful information from my years of experience.

Comments (7)
  • Caitlin

    Thanks for the great article

  • Www.Dospad.Net

    Thank you for the excellent post

  • Christina

    This is truly helpful, thanks.

  • Amber

    Thanks for the excellent article

Leave a Comment